WORKING. LOAD. SINGLE EYEBOLT. AXIAL. MAXIMUM LOAD (W) TO BE LIFTED BY A. PAIR OF EYEBOLTS WHEN THE ANGLE. BETWEEN SLING LEGS IS:.

As soon as a lift begins to occur at any other angle, referred to as angular lift, the rated capacity of the eye bolt begins to diminish. The greater the angle the more drastically the rated capacity is reduced. The chart below shows the impact the direction of pull has on rated capacity: Direction of Pull Rated Capacity

Unlike conventional eyebolts, you can rotate the eye 360° to match the angle of your load. Create your own lifting eye by adding an eye nut to a stud or bolt. Routing Eyebolts These rod end bolts are good for wet and corrosive environments

Crosby® 275 Forged Screw Eye Bolts Crosby® 275 Forged Screw Eye Bolts > Eye Nuts. Crosby® 400 Eye Nuts Crosby® 400 Eye Nuts > Lifting Eyes. Crosby® 405 Lifting Eyes Crosby® 405 Lifting Eyes > Pad Eyes. Crosby® 264 Pad Eyes Crosby® 264 Pad Eyes > Quic-Align.

Dynamo Eyebolts - For Axial loads only (NOT TO BE USED FOR ANGLED LIFTS) vertical (axial lift ) will reduce the rating capacity refer to load charts.

Jun 24,  · Practices to avoid when using lifting eye bolts: Running a Sling Through Eye Bolts. It's often convenient to run a sling through a pair of eye bolts, however, it should be avoided. Attaching a sling in this manner applies angular force to the eye bolts and, as we mentioned earlier, angular forces drastically reduce a lifting eye bolt's WLL.

downguys at bolt hole 73) - See plate GY7SPL. Provisions for downguys are also provided on the steel crossarm and the 3-phase cutout and arrester bracket if required. E. GUY ANCHORS Two basic types of anchoring systems are used for downguys -- one is the screw type and the other is the "Manta-Ray" type.

These eye bolts are designed with a shoulder at the point where the eye and the shank come together. This shoulder design reduces bending stresses on the shank and allows the eye bolt to be used for angular lifting if the shoulder is properly seated in the load.

Regular Nut Eye Bolt Shoulder Nut Eye Bolt Machinery Eye Bolt G-291 G-277 G-279 Important Safety Information— Read and Follow Inspection/Maintenance Safety: † Always inspect eye bolt before use. † Never use eye bolt that shows signs of wear or damage. † Never use eye bolt if eye or shank is bent or elongated.

2. SLING ANGLE. eye bolt capacity chart · 3. CONNECTIONS. The third factor to consider when selecting the correct eye bolt for a lift is to take 

Eye Bolts are load rated and made from forged steel that has been quenched and tempered. Bishop Lifting offers Regular Eyebolts along with Shoulder Eye Bolts, and Shoulder Type Machinery Eye Bolts. All of our eye bolts meet or exceed the requirements of ASME B30.26 including identification, ductility, design factor, proof load, and temperature

Forged Eye Bolt Capacity and Strength Chart to show rated load capacities, must always be applied to eye bolts in the plane of the eye, not at an angle.

Our Collared Eyebolts are fully compliant with AS 2317 and are (b) The angle between the centre-line of the loading on the eye of the eyebolt and the 

See Safe Lifting Chart on page 5. All rated capacities consider a straight vertical lift. Use CAUTION when lifting. Any angle beyond vertical (zero degree) 

case of multi-leg slings the specified angle or range of angles. (2) When using slings in choke hitch multiply the marked SWL by 0.8 to obtain the reduced maximum load the sling may lift ie reduce the safe working load by 20%. (3) With multi-leg slings, when using less than the full number of legs, reduce the maximum load in proportion to the

eye bolt angle chart MP1000 AIR FILTER DONALDSON ECG11-2501 AIR CLE rock crusher liner Z295 KEY REPLACEMENT KEY hard rock crushing. SCREEN-ALL Screen Aggregate Equipment For Sale. Dec 15, · SCREEN-ALL CR176. Screen Aggregate Equipment. Price: USD ,913 USD ,913 + VAT = USD ,850 ( VAT applies to users in

NOTES: The included angle, between the legs of every two-leg sling connected to a load by a pair of eyebolts or eyenuts, should not exceed 90 degrees.

For angle loading, see page 200. S-279 UNC Shoulder Type Machinery Eye Bolts diagrams and charts below before using eye bolt assemblies.

For One Bolt For Two Bolts(Pulling at a 45 Degree Angle) M6: 70: 50: M8: 140: 95: M10: 230: 170: M12: 340: 240: M14: 490: 340: M16: 700: 500: M20: 1200: 830: M22: 1500: 1050: M24:

The Working Load Limit for Eye Bolts is in the direct vertical lifting (b) The angle between the centre-line of the loading on the eye of the Eye Bolt 

Jul 26,  · G-277: SHOULDER NUT EYE BOLT. 2. SLING ANGLE. As the sling angle becomes smaller the tension being placed on the eye bolt increases while the eye bolts capacity diminishes drastically. It is very important that riggers understand this phenomenon completely in order to choose the proper eye bolt to make their lift safely.