Loads may slip or fall if proper eye bolt assembly and lifting procedures are not used. A falling load may cause serious injury or death. Read and understand 

Closed end forged eye bolts with a shoulder are the only eye bolts that are load rated. They must be mounted against a flat surface or washer to 

Failure of lifting eyebolt image. Description of Incident. The deck crew was attempting to move an electric motor weighing approximately 

A major contractor reported an incident that had occurred in which a threaded eyebolt failed during an operation to lift a section of stonework into place. Although there were no injuries

If recommended guidelines are not followed, the failure of a lifting eye can result in loss of property, personal injury, or even death in extreme cases. Forged vs. bent wire

Failure to do so may allow the coil rod to bend and precipitate a premature failure. WARNING: Eye Bolts are intended for straight tension loading only. Angular loading severely reduces the safe workloads and must be avoided or properly considered. See reduction factors below. Performance Data Print Product Email Product Inquire About this Product

Oct 03,  · The first lift with the eye bolt and it pulled out and fell. The eye had threads a size too small and had been JB welded to make the thread fit. FOR SURE never get under a load, never know what could happen. Thanks for that info on safe use of Eye bolts I will remember that.

The lift took place and the eyebolt shanks sheared off. The wellhead equipment was secured and no other damage occurred. EYEBOLT LOCATED ON WELLHEAD. BROKEN 

Jun 6, - Tips for Rigging with Eye Bolts #RiggingSafety #EyeBolts #VMECranes Wire Rope Damage Examples Safety Fail, Crane Lift, Crane Machine, 

A mistake common among untrained riggers is the use of a shackle capable of lifting more than the eye bolt to which it's attached. If, for 

Failure of Lifting Eye Bolt . Similar Alerts. Unsafe Cargo Transfer Using Pallets. Number: 22-06. 2 x incidents reported by a MSF member involving loading of cargo using pallets. View Alert.

Bolts can fail by due to several reasons including (1) the bolt had not been sufficiently preloaded/tension during installation, (2) had lost its preload during service, (3) the applied cyclic loading had been excessive - far beyond the strength of the bolt and/or (4) the bolt had been understrength (quality issue/wrong grade).

The bolts which are used with collars are suitable even for angular loads whereas those which do not have a shoulder are not suitable for angular loads. However, for heavy off-axis loads, an eye bolt with continuous eye and integral shoulder can be used. Be sure to restrict the axis angle to less than 45 degrees.

failure of Crane. There are two main methods to classify an eyebolt. Specifications LIFTING EYE BOLT-TRAPEZIODAL SECTION . ISSN: 2277-3754 ISO 9001: Certified International Journal of Engineering and Innovative Technology (IJEIT) Volume 10, Issue 3, September

Regular eye bolts have a working load limit which should be taken into consideration when used for lifting or supporting an overhead load. They 

When installing tapped type eye bolts DIN 582, When installing stud type lifting eye bolts WN This means that the minimum failure load is.

NB: Please ensure that the safety instructions have been fully read and understood before initial use of the RS bolt-on lifting point. Failure to do so may 

Here are some terms you should familiarize yourself with to help you understand the different types and design of lifting eye bolts: Eye - loop formed at the top that can be either bent, welded, or forged Shoulder - "skirt" where the eye and shank come together designed to resist bending Shank - threaded shaft that attaches to the eye

Inspect and clean the eye bolt threads and the hole. Check for bends, cracks, or worn threads. Screw the eye bolt on all the way down and properly seat. Ensure 

Bolts can fail by due to several reasons including (1) the bolt had not been sufficiently preloaded/tension during installation, (2) had lost its preload during service, (3) the applied cyclic loading had been excessive – far beyond the strength of the bolt and/or (4) the bolt had been understrength (quality issue/wrong grade).

391 products. Eye bolts have a shank for anchoring to structures or equipment and a ring (or loop) at the top for attaching rope, hooks, or other hardware. They're used as anchor eye bolts for routing or tying down wire and cable. Machinery or lifting eye bolts are rated for vertical or angular lifting up to their specified capacity. Application.