Product overview. Fenner Taper Lock® bushes are machined in cast iron and steel and are available in a full range of both metric and Imperial bores and keyways. They have the equivalent to a shrink-on fit on uniform load applications and offer complete ease of installation and removal. The special 4-hole feature on Fenner Taper Lock® bushes

American Metric ® Corporation Ametric Sprockets prepared for American Standard Taper-Lock ® Bushings. Size Part No. Teeth Bushing No. Max. Bore Type Weight - Lbs. (App) Rim Bush Only Only 40TL84 84 13.663 13.372 2 1 1/4 3 9/16 B 11.30 1.70 40TL96 96 15.573 15.282 2 1 1/4 3 9/16 B 14.60 1.70

M - Space required to remove bushing using screws as jackscrews - short hex key - no puller reuired. Listed required hub diameter is for reference only. Severe conditions may require larger hub and in some cases a slightly smaller hub may be satisfactory. Inquire about specific application.

This Ever-Power’s size 3030 taper lock bushing with a torque capacity of 24000 in-lbs is constructed of steel and can be used for installation a taper lock pulley, sheave, or sprocket on a drive shaft. It is flush installed for reduced mounting width and has a split taper for a good clamp to shafts. The bushing is constructed of steel for

Taper Lock® Four Hole Bush Simple, Universal Solution. Machined to exacting tolerances in cast iron and steel, the Fenner Taper Lock four hole bush has been tried and tested in over 60 million applications. It is the most successful shaft fixing in the market place today with a full range of both metric and imperial sizes as well as a full

FENNER Taper Lock® bush metric bore size 3525 Product documents Show all items Product overview Fenner Taper Lock® bushes are machined in cast iron and steel and are available in a full range of both metric and Imperial bores and keyways.

5.800 lb. 1 All bore ranges available in 1/16th inch increments. 2 2 Required. 3 Space required to tighten bushing. Also space required to loosen screws to permit removal of hub by puller. 4 Space required to tighten bushing. Also space required to loosen screws to permit removal of hub by puller. Standard hex key cut to minimum usable length.

Taper Lock Bushes come in a variety of bore sizes, in both metric and imperial. Bush. A. B. D. G. Set Crews. Dia. x Len.

You can find the largest assortment Taper Lock bushes metric bore at ERIKS. Choose from more than 500.000 articles and order right away.

Product documents. Fenner Taper Lock® bushes are machined in cast iron and steel and are available in a full range of both metric and Imperial bores and keyways. They have the equivalent to a shrink-on fit on uniform load applications and offer complete ease of installation and removal. The special 4-hole feature on Fenner Taper Lock® bushes

Taper-Lock Bushings, Size 1008 Part number 1008 x 12.7 Omniclass number 23.27.35.15 CAD models Request for quotation (mm) Bolt Circle (mm) Mounting Screws - Qty. Mounting Screws - Size Mounting Screws - G (deg) Min. Bore (mm) Max. Bore

MPTA-B9i- TAPER LOCK BUSHING AND MATING HUB STANDARD Mechanical Power Transmission Association 5672 Strand Ct. Suite 2, Naples, FL 34110 www.mpta.org Page 1 of 8 MPTA-B9i- TAPER-LOCK BUSHING & MATING HUB

TAPER-LOCK® BUSHINGS. If catalog number ends in an ‘S’ the part is a steel bushing. If catalog number ends in an ‘SS’ the part is a stainless steel bushing. L – Space required to tighten bushing or loosen to remove hub with puller using short hex key. M – Space required to remove bushing using screws as jackscrews – short hex key

Unlike smaller sizes, TB 6050 bushings have M33 metric threads, but other dimensions are derived from inch dimensions. Documents for Download. Dimensions and 

3. Clean and degrease the shaft. Fit the hub with taper bush on the shaft and place in desired position. 4. When using a key, it should be first fitted in the shaft keyway. There should be a

TAPER-LOCK Bushings - Dimensions · 1008 thru 3030 sizes · 3535 thru 5050 Size · 10 X 3.3MM 10 X 5MM 10 X 8MM · 10 X 3.3MM 10 X 5MM 10 X 8MM · 10 X 3.3MM 10 X 5MM 10 

FENNER Taper Lock® bush metric bore size 4535 Product documents Show all items Product overview Fenner Taper Lock® bushes are machined in cast iron and steel and are available in a full range of both metric and Imperial bores and keyways.

Taper Lock Bushes are standard conical bushes used as a locking mechanism for fixing pulleys, Standard range from TB 1008 to TB 5050 for holes from 9.0 to 125.0 mm Inch dimensions from 3/8" to 5" TB 6050, TB 7060, TB 8065 and TB 10085 bushings for

Keyways are British Standard Metric B.S. 4235: Part 1:1972 and conform to I.S.O. recommendations except for the bore sizes marked * which are shallower. Where a 

Power Transmission - Shaft Fixings - Taper Locks Taper lock bush, metric, 3535, 100 mm, Fenner. Taper lock bush, imperial, 3030, 1.1/4 inch, 

Taper Bush Dimensions Metric Taper Bushes Imperial Taper Bushes