forgings ourcing Specialists the Manufacturing & Global ings Dn..aforgings the Manufactunng & Global Specialists ..aforgings ufactur.ng Global Sourcing Specialists the Manutactunng &

Eye-bolt (DIN-580) High-alloyed steel eyebolt. Eye bolts may only be tightened by hand. Safe workload, under a maximum angle of 60° as shown. The lifting eye 

The eye bolts and eye nuts are manufactured from C15, C45 or C15E steel, drop forged and with metric thread. Each eye bolt and eye nut is individually stamped with: Working Load Limit valid for in-line pull thread diameter material identification symbol e.g.

Metric DIN 580 lifting eye bolts are threaded at one end and a loop at the other end. Commonly used in in rigging equipment for vertical or angled loading.

A short eye bolt handbook for designers, intallers and purchasers. DIN 580: STANDARD - LIFTING EYE BOLTS. (July ) This is the technical standard for sale and use of lifting eye

The following guidelines for DIN 580 lifting eye bolts must be observed in addition to the maximum load values given in the table:The eye bolt mus.

forgings ourcing Specialists the Manufacturing & Global ings Dn..aforgings the Manufactunng & Global Specialists ..aforgings ufactur.ng Global Sourcing Specialists

DIN 580 Specification specifies the properties of steel and stainless steel eyebolts and provides information on their correct use in lifting operations (as part of slings and as load handling

DIN 580-LIFTING EYE BOLTS.pdf - Free download as PDF File (.pdf), Text File (.txt) or read online for free.

This is a true fastener, not Anchor Bolt Size Chart Pdf. The displacement of the bolt head within the polymer bes more sieased. Figure 1. 4 1/8. DIN 571 - Hexagon Lag Screws DIN 580 - Lifting Eye Bolts DIN 582 - Lifting Eye Nuts. DIN DIN 601- Hexagon head bolt with nut DIN 603 Mu - Carriage Bolts With Hexagon Nuts DIN 604 - Flat

The following guidelines for lifting eye bolts DIN 580 have to be The eye bolt must be of fully screwed in to achieve a perfect contact.

Material. Lifting eye bolts according to the present Standard shall be manufactured solely from C 15 steel according to DIN 17210. They must be normalized and 

Eyebolts— For Lifting With Shoulder Also known as machinery eyebolts. Zinc-plated steel eyebolts offer good corrosion resistance. 304 stainless steel eyebolts are more corrosion resistant than galvanized steel. 316 stainless steel are the most corrosion resistant eyebolts. Note: Capacities listed are for vertical lifting only.

Lifting eye bolts DIN 580 technical informations Drop-forged steel annealed body, zinc-plated blue passivated, machined contact face. These lifting eye bolts correspond to standard sheet DIN 580. The following guidelines of lifting eye bolts DIN 580 the have to be observed in addition to the load values given in the above table.

LIFTING EYE BOLT - METRIC DIN 580 - FORGED. PART#. 1. All prints must be signed and approved before production begins.

DIN 580. TECHNICAL SPECIFICATIONS. Lifting eye bolts often also called ring bolts are stable ring-shaped fasteners with a fixed threaded part.

Marking: According to standard, WLL, manufacturer C15, thread, CE. Finish: Electro galvanized. Standard: DIN 580. Note: The lifting eyes shall be screwed tight against the surface. When two lifting eyes are used their mutual position shall result in the two eyes at the same level. Larger angle between the slings than 90° are not tolerated.

to the standard: DIN 580 for eye bolts or DIN 582 for eye nuts; • when used as a lifting device, the eye bolt or eye nut should always be fully screwed into the load in such a way that it fits properly against the load; • make sure the thread is undamaged and clean; • eye bolts and eye nuts are free from nicks, gouges and cracks;

DIN 580 Eyebolts Material: Mild steel C15. Minimum breaking load 4 x W.L.L. Meet the WLL requirements of DIN 580. Self-coloured and electro galvanised finish. Marked with size, WLL, C15, ID mark & CE. Supplied with an EC declaration of conformity. W.L.L tonnes

Executions in C15 E zinc-plated steel (DIN 580-ST). INOX DIN 580-NI Code Description d1 d2 d3 d4 h m l k e F1 max. [N] F2 max. [N] F3 max. [N] GN.21401 DIN 580-M8-NI M8 20 36 20 36 10

FEATURES AND APPLICATIONS. The use of DIN 580 lifting eye bolts must take place under the following conditions: - the length of the thread of the assembly hole