Accessories-AWWA C110 or C115 flange) and 8-11 (Details and Accessories-flange faced and drilled per ANSI B16.1 Class 250). Bolts are specified in ANSI B18.2.1 and nuts are specified in ANSI B18.2.2. Bolts and nuts of low-carbon steel conforming to ASTM A307 are specified in the Appendix of AWWA C110 and C115 for flanged pipe when rubber

AWWA Ductile Iron C110 Full Body Bends FILTER BY 123 results for "AWWA Ductile Iron C110 Full Body Bends" Category: AWWA Ductile Iron C110 Full Body Bends Sort Show List View 2 in. Mechanical Joint Ductile Iron C110 Full Body 45 Degree Bend (Less Accessories) Part # FB4LAK Item # 1318187 Mfr. Part # 056348 To see availability for this product,

ANSI/AWWA C110/A21.10, NFPA 13/24, 3” - 12” UL listed and approved (File - Tyler Union). MATERIAL: Cast of ASTM A536 qualified ductile iron.

factured to ANSI/AWWA-C110/A21.10 standard. These fittings have identical face to face and center to These fittings have identical face to face and center to face dimensions and the same

Look Inside This standard covers 3- to 48-in. (76- to 1,219-mm) gray-iron and/or ductile-iron fittings to be used with ductile-iron pipe for water.

AWWA C110 applies to ductile iron and gray iron flanges and fittings. AWWA C207 was developed more recently and applies to steel flanges and fittings. As these standards are designed for cold water service, their pressure ratings are higher than ASME/ANSI ratings for a fitting of similar size and material; this is because ASME/ANSI fittings are

3. AWWA C401 The Selection of Asbestos Cement Distribution Pipe, 4 inch through 16 inch for Water and Other Liquids. 4. AWWA C402 Asbestos-Cement Transmission Pipe 18 inch through 42 inch for Potable Water and Other Liquids. 5. AWWA C403 The Selection of Asbestos-Cement Transmission and Feeder Main Pipe, 18 inch through 42 inch. 6.

AWWA C110 Class 250 (3"~24") Add suffi x "C" for Grey Cast Iron - "D" for Ductile Cast Iron TEES & CROSSES REDUCING TEE (on Run and/or Branch) 5 Size Part No. HJ TT1 Weight Tee Cross Tee Cross-Tel: 877-766-4459 • Fax: 877-766-4458 • Website: www.unitedwaterproducts.com Larger sizes thru 48" available upon request.

AWWA Headquarters 6666 W. Quincy Ave. Denver, CO 80235 USA Phone: 303.794.7711 or 800.926.7337 AWWA Government Affairs Office 1300 Eye St. NW Suite 701 Washington, DC 20005 USA Phone: 202.628.8303 AWWAIndia Association New Delhi, India https://www.awwa-india.org

AWWA C110 Full Body DI MJ Fittings are commonly used in municipal pressure systems.Fittings are available in 2 – 64 in for used on PVC and DI Pipe.

Standard: AWWA C110 (flange fittings), AWWA C153(MJ fittings). Working pressure: MJ fittings: 350 PSI rating for 4"-24"sizes,250 PSI rating for 

As one of the leading awwa c110 flange and flare manufacturers and suppliers in China, we warmly welcome you to buy bulk awwa c110 flange and flare made in 

Note that there are two other AWWA flange standards as well; AWWA C110 (ductile iron/gray iron flanges) and C228 (stainless steel flanges). These standards also tend to follow similar dimension rules as AWWA C207 (i.e. ASME B16.1, B16.5, B16.47, etc.). Table 1 and 2 provide a side-by-side comparison for reference. The Confusion

PDF ANSI/AWWA C110/A21 DRILLING: In accordance with ANSI/AWWA C110/A21.10, ANSI/AWWA C153/A21.53 and ANSI B16.1 Class 125 Flanges CEMENT LINING: In accordance with ANSI/AWWA C104/A21.4 -- sizes 1"- 3" single thickness and sizes 4"- 64" double thickness COATING: Asphaltic seal coat inside in accordance with ANSI/AWWA C104/A21.4 and

This standard describes 3-in. through 64-in. (80-mm through 1,600-mm) flanged ductile-iron pipe with ductile-iron or gray-iron threaded flanges for potable water, wastewater, and reclaimed water service. Flanged pipe and flanges are rated for a maximum working pressure of 250 psi (1,720 kPa). However, 24-in. (600-mm) and smaller flange joints

AWWA C110, ANSI A21.10 UNITED BRAND FITTINGS. reducers, and blind fl anges. All are manufactured in strict accordance with AWWA C110, ANSI A21.10. Material: Ductile Cast Iron, ASTM A536, Grey Cast Iron, ASTM A-126 Flange: Faced and drilled in accordance with ANSI B16.1 Class 125 Lining: The standard lining is cement mortar with bitumen overlay

AWWA's Second Comment Period on ANSI/AWWA C110/A21.10-XX - Ductile-Iron and Gray-Iron Fittings Attachment. August 20, AWWA solicits public comments on all proposed new AWWA Standards, and on all proposed revisions, reaffirmations, or withdrawals of existing AWWA Standards.

NAPAC's “United” Brand Flanged Fittings are manufactured from high strength ductile iron and are made in accordance to the latest AWWA C110 ANSI A21.10 

UNITED DUCTILE IRON CLASS 250 FLANGED FITTINGS Bends AWWA C110, ANSI A21.10 90 Reducing Bends Size Part No. A R T T1 Wgt. 4 x 3 W-10F-0403-D 6.5 4.5 .52 .48 33 6 x 3 W-10F-0603-D 8.0 6.0 .55 .48 45 6 x 4 W

COATING: • Interior of fitting is seal coated (asphaltic material) in accordance with ANSI/AWWA C104/A21.4 and NSF61 approved. • Exterior of fitting is seal coated (asphaltic material) in accordance with ANSI/AWWA C110/A21.10 and NSF61 approved. GASKETS: • SBR in accordance with ANSI/AWWA C111/A21.11. • Also available in EPDM, NBR and CR.

Shop for AWWA Ductile Iron C110 Full Body Tees at Ferguson. Ferguson is the #1 US plum supply company and a top distributor of HVAC parts, waterworks supplies, and MRO products.