3:1 pilot ratio, standard capacity counterbalance valve. CAPACITY: 120 L/min. | CAVITY: T-2A. L. Control. Standard Screw. Adjustment.

Counterbalance valves should be set at least 1.3 times the maximum load induced pressure. Turn adjustment clockwise to decrease setting and release load. Full clockwise setting is 200 psi (14 bar). Approximately 1 drop (0,07 cc) of fluid will pass from the pilot area to the vented spring chamber every 4000 cycles. Available on back-order

Sun Hydraulics Counterbalance Valve Type: CBCH LCN di Tokopedia ∙ Promo Pengguna Baru ∙ Cicilan 0% ∙ Kurir Instan.

Sun Hydraulics' LoadMatch Counterbalance Valves control settings at reduced loads to help minimize energy wasted during low load machine cycles.

SUN HYDRAULICS RVCA LCN. 100% ORIGINAL.

Functionally, it is a counterbalance valve that seats as a poppet valve and modulates as a spool valve, offering the best of both worlds. A built-in dampening 

Product Description Warranty CBCALAN COUNTERBALANCE VALVE STANDARD CAPACITY 3:1 PILOT RATIO 15 GPM CAPACITY 3075 PSI MAX LOAD PRESSURE 4000 PSI MAX SETTING 3.75 ADJUSTMENT/CCW 7/8 IN VALVE HEX SIZE 9/16 IN LOCKNUT HEX SIZE 5/32 IN ADJUSTMENT SCREW INTERNAL HEX SIZE FACTORY WARRANTY MAY NOT APPLY. RADWELL 2-YEAR WARRANTY INCLUDED

Sun Hydraulics CBCG-LJN Counterbalance Valve - Three Port Counterbalance valves with pilot assist are meant to control an overrunning load. The check valve allows free flow from the directional valve (port 2) to the load (port 1) while a direct-acting, pilot-assisted relief valve controls flow from port 1 to port 2.

Fixed setting, 1.5:1 pilot ratio, semi-restrictive counterbalance valve. 3:1 pilot ratio, standard capacity, LoadAdaptive™ counterbalance valve. 7:1 pilot ratio, vented counterbalance – valve

Sun Hydraulics CBEA-LHN Counterbalance Valve - Three Port Counterbalance valves with pilot assist are meant to control an overrunning load. The check valve allows free flow from the directional valve (port 2) to the load (port 1) while a direct-acting, pilot-assisted relief valve controls flow from port 1 to port 2.

Counterbalance valves should be set at least 1.3 times the maximum load induced pressure. Back pressure at port 2 adds to the effective relief setting at a ratio of 1 plus the pilot ratio times the back pressure. Standard, 5000 psi Maximum Setting Load holding to 3850 psi with 5000 psi valve setting Maximum valve leakage at reseat = 5 drops/min.

FEATURES: Interchangeable with Sun Hydraulic®; Prevent a load from drifting caused by spool valve leakage; Prevents a load from dropping in case of hose or 

Counterbalance valves with pilot assist are meant to control an overrunning load. The check valve allows free flow from the directional valve (port 2) to 

Relief Valve Comparable Replacement to Sun Hydraulics RPEC-LAN. 2. $7000. Get it Fri, Sep 9 - Wed, Sep 14. FREE Shipping. SN CBEG LJN - Sun Counterbalance Valve. T-2A Cavity. 2000-5000 PSI. 25 PSI Check. 30 GPM Max. 4.5 to 1 Pilot. $16864. Get it Fri, Sep 2 - Wed, Sep 7. Doering manufactures valve and pump products for fluid power applications.

CBEA-LAN Sun Hydraulics Cartridges standard capacity counterbalance valve For Hydraulic CBCG-LJN sun cartridge hydraulic counterbalance valve Load valve.

Sun Hydraulics 1.5:1 pilot ratio, standard capacity counterbalance valve. 1. CBEB. 1.5:1 pilot ratio, standard capacity counterbalance valve.

Sun counterbalance cartridges can be installed directly into a cavity machined in an actuator housing for added protection and improved stiffness in the circuit. Two check valve cracking pressures are available. Use the 25 psi (1,7 bar) check unless actuator cavitation is a concern.

www.sunhydraulics.com 202 Sun Hydraulics Pub. -0-28 Technical Tip Counterbalance Pilot-to-Open Check Cartridges Back pressure on standard non-vented counterbalance valves causes

Sun Hydraulics Counterbalance Cartridge Valves 1.5:1 pilot ratio, standard capacity counterbalance valve. 2:1 pilot ratio, standard capacity 

Sun Hydraulics Corporation continues its pursuit of the perfect counterbalance valve.

Counterbalance valve Stage 1. Stage 1 – The directional valve is centered: ports 2 and 3 are directed to tank. The counterbalance valve spool and check valve are closed which prevents oil flow out of the cylinder rod, thus preventing the load from lowering. This is why counterbalance valves are used – to prevent the load from moving when