C-FACE · 143TC & 145TC – 2 3/4” instead of 2 1/4” · 182TC & 184TC – 3 1/2” instead of 2 3/4” · 213TC & 215TC – 4 1/4” instead of 3 1/2” · 254TC & 256TC – 4 3/4” 

Motor. Mounting. Flange. Motor Flange Dimensions Single Reduction Flange Mount. Servo Input. Servo Input. C-Face Input. Notes: Other servo flanges and bore 

U dimension). C flange motors always have threaded mounting holes in the face of the motor. D — The “D” flange has a special type of mounting flange 

The flange diameter is bigger than the motor frame diameter. The holes are not tapped. B5 flanges are available for all motor sizes. B14A - flange ('C' face) The flange diameter is smaller than the motor frame diameter. The holes are tapped. Available up to 160frame. B14B - flange The flange diameter is between B14A & B5 flange.

SEW motor with NEMA-C-Face flange with inch dimensions and threads. • NEMA MG1. Description. The flange-mounted motor in the /FC design is the design with 

ISO 3019-1. "Dimensions and identification code for mounting flanges and shaft ends of displacement pumps and motors". Two bolts mounting flange Two bolts mounting Four bolts mounting flange Four bolt mounting Straight (cylindrical) keyed shafts without thread Straight (cylindrical) keyed shafts 30° involute splined shafts

In DIN EN 50347, the frame sizes are allocated flange FF with through holes and flange. FT with tapped holes. The designation of flange A and. C according 

TABLE 6 - NEMA 'C' Motor Dimensions MAGNALOY'S HORIZONTAL PUMP/MOTOR MOUNTS are available for mounting NEMA C'face motors in frame sizes 56C through 449TSC to most SAE and Metric 2 and 4 bolt pump flanges. A MOUNT KIT is included which contains all bolts and washers required to attach the pump and motor to the mount.

Approx. Dimensions ’ * * + , 4 ; 284T 180M 22 x 32 x 22 286T 180L 22 x 32 x 22 324T 200M 29 x 42 x 26 326T 200L 29 x 42 x 26 364T 225S 29 x 42 x 26 365T 225M 29 x 42 x 26 404T 250S 32 x 51 x 30 405T 250M 32 x 51 x 30 444T 280S 32 x 51 x 30 445T 280M 32 x 51 x 30 447T 40 x 56 x 33 W ˚ ˇˇ ˙˝˛ BC Cast Iron BA Aluminum

STEP 2: Determine the design of the electric motor · B3: Foot only · B5: Outer flange (flange diameter exceeds that of the motor) · B14: Inner flange (flange 

feet above motor. b14 "c" type face at drive end, no feet. b17 2 "c" or "d" type flanges, foot mounted. v1 "d" type flange at drive end , shaft down, no feet. v3 "d" type flange at driv e end, shaft up, no feet. v5 vertical foot, wall mounted, shaft down. v6 vertical foot, wall mounted, shaft up v18 "c" type face at driv e end, shaft down, no

Choose from our selection of C-face motors, including face-mount AC motors, base/face-mount AC motors, and more. In stock and ready to ship. Motor Frame Size. Motor Frame Size; NEMA 56C: IEC 112M: IEC 80M: IEC 100L: NEMA 145TC: IEC 90L: IEC 90S: Electrical Phase. Flange Type: Dia. Lg. Center to Base: Class: Max. Temp., ° F: Cannot Be

Just to determine what flange and shaft of pump or motor you have, please see below excerpts from the next standards: SAE J744. “Hydraulic Pump and Motor Mounting and Drive Dimensions”. ISO 3019-1. “Dimensions and identification code for mounting flanges and shaft ends of displacement pumps and motors”. Two bolts mounting flange

SAE PUMP AND MOTOR MOUNTING FLANGE AND SHAFT DIMENSIONS : SAE Straight (keyed) Shafts SAE Code Shaft DIA (D) Shaft Length (SL) Total Length (TL) Key Width . AA : 0.500 . 0.750 : 1.062 . 0.125 SAE Two Bolt Mounting Flange . SAE Code : Bolt PCD . Bolt Hole DIA : Pilot DIA (P) Pilot Length (PL) AA . 3.250 : 0.406 . 2.00 : 0.250 . A : 4.187 . 0

Frame Suffix Letters · C = C flange mounting · D = D flange mounting · P or PH = Vertical P or PH flange mounting · T = Standard shaft for belted service · TS = 

NEMA C face motors with a rigid base have different BA dimensions in the following instances: 143TC & 145TC – 2 3/4” instead of 2 1/4”. 182TC & 184TC – 3 1/2” instead of 2 3/4”. 213TC

Foot Mounting. Shaft. B5 Flange. B14 Face. General. Frame. Type. A. B. C Industrial Electric Motors and Drives. Key and Keyseat Dimensions. Frame.

Spline Details Nominal DIA (ND) Total Length (TL) AA 9T 20/40 DP 0.500 1.062 A 9T 16/32 DP 0.625 1.250 AH 11T 16/32 DP 0.750 1.490 B 13T 16/32 DP 0.875 1.625 BB 15T 16/32 DP 1.000 1.812 C 14T 12/24 DP 1.250 2.187 CS 21T 16/32 DP 1.375 2.187 CC 17T 12/24 DP 1.500 2.437 D 13T 8/16 DP 1.750 2.937 E 13T 8/16 DP

flange, the flange diameter is larger than the body of the motor and it has clearance holes suitable for mounting bolts to pass through from the back of the motor into threaded holes in the mating part. “D” flange motors are not as popular as “C” flange motors. H — Used on some 56 frame motors, “H” indicates that the base is

dimensions listed are identical for either rigid or resilient base mounting. For 56H Combination Foot, refer to Diagram 1. For C Flange motors, refer to Diagram 2. Diagram 1 Suffix “Y” =

Aluminum Frame (Single & Three-Phase) Motors. IM B14 / IM B5 - Flange Dimensions. IM B14 - C Flange & IM B5 - D Flange. All dimensions in mm. B14. B14.