SIZING CHARTS 2-xxx Sizes, Cross-Section: .210 ± .005 in (5,33 ± 0,13mm)

Parker's Fluorocarbon 50 Durometer O-Ring, General Purpose , Brown V0986-50 is the softest FKM material offered for O-rings. V0986-50 has excellent compression set resistance coupled with the wide chemical resistance expected of a fluorocarbon. *Custom sizes and coatings/markings are available upon request. Contact Parker O-Ring Division at

O-Ring Tolerance Charts. Application Specific Material and Design Support. Fast-Expert-Quality-Service. O-Ring Tolerances AS568 Standard USA Parker Sizes Military. AS568 O-Ring Size AS568 O-Ring ID (Inches) AS568 O-Ring ID Tolerance (Inches) AS568 O-Ring Actual CS (Inches)

O-rings are circular sealing elements with circular cross-sections, and are mainly used in static applications. The sizes are specified by the inside diameter and the cross section diameter. Our O-rings are manufactured according to metric and imperial international standards such as AS 568B, DIN ISO 3601 and JIS. Custom sizes of almost any dimension are possible, such as

Parker 5‑XXX Size CS (MM) ID (MM) CS (IN) ID (IN) 5‑002 1.50 10.57 0.059 0.416 5‑003 1.50 21.23 0.059 0.836 5‑004 1.65 27.18 0.065 1.070

Sizes Parker Hannifi n Corporation • O-Ring Division 2360 Palumbo Drive, Lexington, KY 40509 Phone: (859) 269-2351 † Fax: (859) 335-5128 www.parkerorings.com Parker O-Ring Handbook Parker Series 3-XXX O-Ring Sizes These O-rings are intended for use with internal straight thread fl uid connection bosses and tube fi ttings. Ref. MS33656

The Parker O-Rings for gauges sizing device is used for checking any sample O-Ring up to eight (8.00″) inches in diameter to determine the nearest standard 

When part numbers are missing, seal dimensions are unknown, and the parts themselves are unavailable from the equipment OEM, these o-ring kits can save the day, 

Parker's Fluorocarbon 50 Durometer O-Ring, General Purpose , Brown V0986-50 is the softest FKM material offered for O-rings. V0986-50 has excellent compression set resistance coupled with the wide chemical resistance expected of a fluorocarbon. *Custom sizes and coatings/markings are available upon request. Contact Parker O-Ring Division at

Gallagher Fluid Seals has published our newest sizing guide, the Parker 5-Dash Series. Parker's 5-Dash series of o-rings are classified as 

Resilon® Polyurethane O-Rings (568) Resilon® polyurethane O-rings for hydraulic and pneumatic applications, static and dynamic AS568B specification size O-ring grooves (568). Configure

Sizes. Parker Series 3-XXX O-Ring Sizes. These O-rings are intended for use with internal straight thread fluid connection bosses and tube fittings. Ref.

AS568 I.D ± C/S ± O.D I.D ± C/S ± O.D ‑001 0.029 0.004 0.040 0.003 0.109 0.74 0.11 1.02 0.07 2.78 ‑002 0.042 0.004 0.050 0.003 0.142 1.07 0.11 1.27 0.07 3.61 ‑003 0.056 0.004 0.060 0.003 0.176 1.42 0.11 1.53 0.07 4.48

Parker 5-XXX Series Size Chart. Parker Hannifin has established the 5-XXX series for a number of commonly used o-rings sizes which do not fall in the AS568 line of o-rings and are also not true “metric” sizes. The chart below lists all of these sizes with their corresponding dimensions in inches and millimeters for easy identification.

Use our o-ring size chart and calculator to find the AS568 or metric sizing of standard size HNBR, Viton, and other o-rings. Go to Navigation Go to Content. O-ring Sizes: Standard and Metric : Size: Nominal Size: Standard Size : Metric Size : inches: inches : millimeters :

Parker Hannifin Corporation. Tube Fittings Division. Columbus, Ohio http://www.parker.com/tfd. O3. 4300 Catalog. O-Rings and Seals. Dimensions for reference 

Parker O-Ring Sizing Cone : Amazon.in: Jewellery.

14. O-ring Size Charts Note: The AS O-ring Size Chart has a column that shows the Nominal Size along-side the Actual Size. Originally the nominal size was just for a listing of the approximate fractional dimensions of the O-ring. Prior to the common use of dial calipers many people called out a 1 inch by 1-1/4 rt = O-ring, this was a dash -214

b) This chart provides dimensions for standard (AN) shrinkage materials ONLY. These correspond to AS568A dimensions. O-rings manufactured out of compounds 

Parker´s O-Ring Selector is an engineering tool which offers O-ring material and size selection combined in one tool. Both are interlinked, thus ensuring the best possible combination of the calculated O-ring size and material choice. The O-Ring Selector covers both imperial and metric standards. Service Conditions & Material Selector

Standard sizing charts for o-rings, AS568 standard metric JIS BS Parker o-rings, x-rings, and square-rings Standard and custom o-rings in stock order