In the vast majority of common hydraulic hoses, the I.D. measurement is divided into 1/16" increments known as the "dash size.". For example, a hose measuring 3/4" ID will be shown as a "-12" coming from the numerator of the fraction of 3/4″= 12 /16". A 1" ID would be 16 /16 or a -16, and so on. There are notable exceptions to

How to select the hose size for given flow volume and velocity. Graphs for cubical expansion of hoses. Tightening torque of hose couplings and adapter.

Improper length may reult in inferior performance to catalog specification. ○Never repair or rework a hose assembly. Old or used hose assemblies do not have 

www.eaton.com/hydraulics. Part numbers and dash sizes Hose size (in 16ths of an inch) Fitting Selection Chart for Select Synflex Hose. Synflex Hose.

Trim Size: Bleed: Live/Safe: Finished Size: Scale: Colors: Resolution: # of Pages: Binding/Finish: 8.5" x 11" 0.125" 8.5" x 11" 100% 4C 300 dpi 4 Cover Notes: Stock Photography: Purchased: MAGENTA HOLE PUNCH DOES NOT PRINT OffsetComp_105547 (pg 2) YES (Pulled from COTGEN17050) Hydraulics Brochure Hydraulic Hose, Fittings & Equipment

HYDRAULIC COUPLING IDENTIFICATION CHART Mated angle seat with O-ring This type of seal is found on BSP and DIN terminations. It uses both the O-ring and the mated angle Dash Size Nominal Size No. Threads per Inch Male Thread O.D. (mm) -2 1/8" 28 10.1-4 1/4" 19 13.6

size of the connecting end and the second two numerals indi-cate the size of the hose end. All other fittings are followed by a dash number which is the nominal size of the fitting expressed in 16ths of an inch. Where two dash numbers are given, the first one generally indicates the pipe or port size and the second indicates the tube or hose size.

Metric 60° Cone. DIN 7631. The male connector has a 60° recessed cone and a straight thread; the has a straight thread as well, and a globeseal seat. The seal forms between the recessed cone on the male and the tapered nose of the female. The threads of both halves mesh to form a strong mechanical bond.

Hose Fitting Hose I.D. Product Code Crimp Diameter +/- .005" (0.13 mm) Recommended Die Set Select the die for your crimper below Micrometer Setting SAE 100R3 General Purpose/Hydraulic Hose (R3) D100 D165 D205 Braided / U Series Hose Fittings crimp to knurl 1/4" R3-04 0.615" (15.60 mm) D100-14MM D100-14MM D200-14MM 1.60

Hydraulic suction & delivery hose for fuels & High pressure hydraulic hose for jacking applications sizes) range of hoses exclusive to Pirtek.

Dash sizes following the base part number indicate fi rst the nominal thread or tube size, and lastly the nominal hose diameter. Please note that for truck hoses, notably SAE100R5 and SAE100R14, the nominal hose size does not exactly match the actual inside diameter, since these hoses were designed to replace common copper tubing.

12/3 · ID is the hydraulic hose inner diameter, OD is the outer diameter, so ID, OD can determine the hydraulic hose size. You can see the hydraulic hose structure, to get a clue about hydraulic hose sizing. The ID and OD sizes are very important, they can’t be too small or too big. The proper inner diameter can ensure the hydraulic fluids inside

This chart is designed as an aid in selecting the correct hose size. • In case of the velocity for pressure line is 6m/sec and the necessary volume is 

Lay a straight edge across these two points. The straight edge crosses the centre column just above the -08 on “All Other Dash Sizes” side of Hose Bore axis. Keeping the straight edge on 40 litres per minute, cross the centre column at -08 and -10 sizes and read the Flow Velocity in the right hand column. It can be seen that using -08 Hose

the hose size, and Isobaric hoses, where working pressure is constant across all sizes according to the specifications of ISO 18752. PREMIUM.

industrial and hydraulic rubber hoses segment, with 16 plants, 79 subsidiaries and assembly plants and bend radius listed for each hose size and type. Maximum crimp data charts. Extensive impulse testing has been performed by ALFAGOMMA to verify the recommendations contained in this catalogue. A simple burst or pressure test cannot

Hydraulic fitting size chart DIN fitting size chart May 28, 2019. DIN fittings size chart is acc to 2353 compression fittings, with cutting ring. End connections as follows: Male tube end with 24 deg cone; swivel nut with o-ring cone; male tube end bulkhead

from rupture or blow-apart of a hydraulic hose assembly that is: pressure ratings through all sizes make hose identification and selection easier and 

designs. Dash sizes = Size of hose ID in sixteenths of an inch. Reduced bore hose is an exception to the rule. Refer to “How To Read Hose Part Numbers” 

HOSE TYPE SPECIFICATION INCH DASH DN 3/16 - 04 5 1/4 - 05 6 5/16 - 06 8 13/32 -08 10 1/2 -10 12 5/8 - 12 16 7/8 - 16 22 1 1/8 - 20 29 1 3/8 -24 35 1 13/16-32 46 FLEXOR 5 SAE 100 R5

Wire Braid Hydraulic Hose: SAE 100 R1AT/DIN EN 853 1SN STANDARD Tube: Oil resistant synthetic rubber Reinforcement: one high tensile steel wire braid Cover: Abrasion and weather resistant synthetic rubber Temperature range: -40 ℃ to +100 ℃ Author: Administrator Created Date: 10/12/ 5:12:26 PM